07:35:00
On time
Couplers0 kN
40
0points
Next stopMill Lane1.90 km
Due07:39On time
Next signal
660 m
Limit
40
Next limit90in 150 m
GradientLevel
AWS
Vigilance
Doors
ATP
Wheel slip
Advice

HARBOUR LINETrain driving simulator

Paused

The train and the clock are stopped.

How to drive

  • Push the controller into power (P1 to P5) to accelerate. Pull it into brake (B1 to B7) to slow down. Brakes take a moment to build up.
  • Stop with the front of the train at the stop marker, open the doors, and close them when boarding is complete.
  • The starting signal clears at departure time. A red signal means stop: passing one ends the run.
  • A yellow signal means the next one is red. When the AWS horn sounds, press Acknowledge within three seconds.
  • Press Acknowledge when the vigilance buzzer sounds, or the brakes apply on their own.
  • Sound the horn between each W board and its level crossing.
  • Freight, BUILD IN YARD: start in the shunting yard, collect any wagons you want in any order, stop at the EXIT board, and the train you made up goes out on the line.
  • Tap the route button on the start screen to choose from six routes: the Harbour Line to Kestrel Hill or Seaview Sands, the Ghat Line up steep mountain grades through five tunnels, the Metro Line with ten close stops and trains passing on the other track, the 20 km Coalfield Line from the colliery to the port, and the Desert Line at 130 km/h.
  • On curves the view leans with the train at speed. You can turn this off in Settings, Tilt on curves.
  • Yellow boards mark a temporary speed restriction for track work. Sound the horn after the warning board, keep to the limit until the T board.
  • Request stops: if nobody is waiting and no one wants to get off, you may run through. The cab shows "(request)" next to the station.
  • Listen to the signaller on the radio. A car stuck on a crossing or cattle on the line means stop short; a long horn blast moves the cattle on.
  • Overshot a platform? Stop, select reverse, and set back at walking pace.
  • Free drive has no signals, timetable or scoring: drive anywhere in either direction and open the doors at any platform.
  • Air brakes need time to recharge after each release, freight trains most of all. Make one steady brake application rather than braking on and off, or the brakes get weaker. The blue needle on the brake gauge is the brake pipe.
  • Wheel slip: each locomotive can only pull as hard as its wheels grip the rails, less at speed, much less on wet rails or where leaves have fallen (shown as "Leaves" on the track strip). Ease the power or use sand (X, or the Sand button on a freight). With Assist on, the slip control and sanding work by themselves.
  • Couplers: the Couplers meter shows how hard the train is being pulled (green, amber, red) or pushed together (blue). Notch up gradually from a stand, never take power while the rear brakes are still releasing, and brake smoothly. Too much pull snaps a coupler and ends the run. A hard run-in costs points.
  • On a long train the brake signal travels back wagon by wagon, so the rear brakes apply and release several seconds after the front. Extra locomotives on a freight run mid-train as helpers and share the pull. After an ATP brake, return the controller to Off before power comes back.
  • Dynamic brake: on locomotives that have one, B1 and B2 (blue on the controller) brake with the locomotive's motors and use no air, ideal for holding speed down long gradients. From B3 the air brake adds to it. It fades out at low speed, where the air brake takes over.
  • Ghat Line freights: stop at the BANKER board just past Riverbend. A banker engine couples on behind and pushes, following your power handle, until the train is over the top of the climb.
  • Freight: a heavy train limited to 80 km/h. Pass each station on time and stop at the terminus. It brakes and climbs much slower than a passenger train.
  • Shunting yard: push wagons into the sidings in reverse and pull them out forward. Set the points (T) for the road you want, buffer up at walking pace to couple, and uncouple with U (behind the loco) or keys 1 to 5, or tap a numbered coupling. Make up the train shown on the display and stop at the EXIT board. Yard limit 15 km/h. Levels unlock one by one: finish within the par number of moves, with no penalties, for three stars. In sorting levels, leave each wagon in the road whose number board matches its destination card.
W or ↑Controller one notch toward power
S or ↓Controller one notch toward brake
NController to neutral (coast)
EEmergency brake
SpaceAcknowledge AWS warning or vigilance alarm
DOpen or close the doors
APassenger announcement for the next station
RChange direction (forward or reverse) while stopped
H (hold)Horn
LHeadlights
IIndependent loco brake on or off (brakes only the locomotive)
XSand the rails for better grip
BLocomotive bell on or off (in the yard it rings while you move)
TShunting yard: change the points
U, 1–5Shunting yard: uncouple behind the loco, or at that numbered coupling
P or EscPause
MSound on or off

On touch screens, drag the controller handle and tap the console buttons.

Settings

Run

Departure
Weather
Driver aids
Graphics
Tilt on curves

Departure time and weather apply from the next run.

Sound

Announcements
Voice
Filler sounds

Choose a route

Sound files

The locomotive, horn, bell, wheels, brakes, coupler and crossing bells use real recordings built into the game. Add your own files to replace them, or to add station ambience, door sounds, a chime and recorded announcements. Files stay on this device.

Name files like horn.mp3, idle.wav, notch1.wav, station.mp3, chime.mp3 and they are matched automatically.
Recording credits

Diesel locomotive engine (EMD 645 turbo), Nathan K5LA horn and coupler: JMRI VSDecoder sound sets, GPL-2.0; horn recorded by Ted Najzer. From Pixabay: locomotive bell "Diesel Locomotive E Bell Loop" by caboose_canine; wheels on rails "Train Sound", rail joints "Train track joints slow loop" by freesound_community; loose track rattle "Loose railway track sound" by arunangshubanerjee. Brake squeal: JMRI VSDecoder Class 64 set, GPL-2.0. Level crossing bells: "RRCrossing.wav" by Mark_Ian, edited by Wuzzy (OpenSFX), CC0 1.0. Announcements use your device's built-in voice unless you add recordings.